Форум АСУ в Україні

форум з автоматизації для викладачів, студентів та спеціалістів
Сьогодні: 28 березня 2024, 22:33

Часовий пояс UTC + 2 годин [ DST ]




Створити нову тему Відповісти  [ 1 повідомлення ] 
Автор Повідомлення
 Тема повідомлення: Friction Fundamentals and Accelerating Cars
ПовідомленняДодано: 27 серпня 2014, 23:44 
Офлайн
Викладач

З нами з: 29 листопада 2013, 17:11
Повідомлення: 5033
Friction Fundamentals and Accelerating Cars
In elections, it’s always the economy; in engineering, it’s the fundamentals
http://e-ditionsbyfry.com/Olive/ODE/CTL ... w=document
Цитата:
Friction may well be nature’s most useful phenomenon. Without it, walking would be impossible and there would be no belt drives, no clutches, no wheels and no brakes. However, in machinery in which it is not the driving force, friction is an undesirable parasitic effect, generating heat, causing wear and wasting energy. So whether the goal is to reduce friction or enhance it, the proper combination of geometry, materials and lubrication must be employed in a design, i.e., a proper tribological approach. Tribology is the study of friction and wear and it has been estimated that the correct application of tribology throughout U.S. industry could save the country $500 billion annually.
We have all read about the problems with uncontrolled acceleration of automobiles due to faulty accelerator pedals. Friction has been identified as the likely culprit, and the proper combination of geometry, materials and lubrication will likely lead to a solution. Why did this happen? It is too early to answer that question with any certainty, but I do know that most engineers, including mechanical engineers, do not fully understand the friction phenomenon. Failure to understand the fundamentals of such a pervasive physical effect is bound to lead design failures, some of which might be catastrophic.
Stick-slip motion is a common behavior associated with friction. A typical stick-slip experiment is to attach one end of a spring to a block sitting on an unlubricated horizontal surface. The other end of the spring is moved horizontally with a constant velocity. How will the block move? Of course it is highly dependent on the physical system parameters, but one possible outcome is stick-slip motion, as shown in the figure above. When the spring force exceeds Fstick, the mass accelerates, the spring elongates and the mass comes to rest. The process then repeats, creating the stick-slip behavior. A model used to describe the friction phenomenon must be able to show this behavior. The automobile accelerator pedal relies on a balance between the return-spring force and sliding friction, which could vary over time due to wear and contamination, to perform effectively and safely.

Зображення


Догори
 Профіль  
 
Відображати повідомлення за:  Сортувати за  
Створити нову тему Відповісти  [ 1 повідомлення ] 

Часовий пояс UTC + 2 годин [ DST ]



Хто зараз онлайн

Зараз переглядають цей форум: Немає зареєстрованих користувачів і 1 гість


Ви не можете створювати нові теми у цьому форумі
Ви не можете відповідати на теми у цьому форумі
Ви не можете редагувати ваші повідомлення у цьому форумі
Ви не можете видаляти ваші повідомлення у цьому форумі
Ви не можете додавати файли у цьому форумі

Знайти:
Вперед:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Вы можете бесплатно создать форум PHPBB2 на MyBB2.ru, Также возможно создать форум бесплатно PHPBB3 на Getbb.ru
Український переклад © 2005-2007 Українська підтримка phpBB