Форум АСУ в Україні

форум з автоматизації для викладачів, студентів та спеціалістів
Сьогодні: 29 березня 2024, 02:34

Часовий пояс UTC + 2 годин [ DST ]




Створити нову тему Відповісти  [ 1 повідомлення ] 
Автор Повідомлення
 Тема повідомлення: Power Control: Advanced Process Control
ПовідомленняДодано: 19 серпня 2014, 17:30 
Офлайн
Викладач

З нами з: 29 листопада 2013, 17:11
Повідомлення: 5033
Power Control: Advanced Process Control
Control and stabilization of a multiple boiler plant can be improved by using an advanced process control (APC) approach.
http://www.controleng.com/single-articl ... 73744.html
Цитата:
Coal-fired boilers are used in many industrial processes, the most prominent being steam generation for utilities and power plant turbines. The primary objective of a boiler is to achieve optimum operating efficiency with high reliability and low cost. Techniques to improve boiler operation in the past decade have largely focused on optimizing boiler performance while simultaneously adhering to environmental constraints. Model predictive control (MPC) has become an increasingly popular replacement for traditional boiler control and optimization.
Advanced process control (APC) and MPC have been used in industry to stabilize and optimize plants. Stable control on boiler key combustion parameters balances the burner management system, reducing thermal stress factors and equipment degradation from unstable control.
Environmental legislation requires power generation utilities to reduce harmful gases such as nitrous oxides (NOx) and carbon monoxide (CO) emissions from coal-fired boilers. Tight dynamic control of variables is an interactive process that requires a multivariable controller; this process can increase boiler efficiency and reduce production of NOx. Model-based APC was implemented in a coal fire power generation plant to adhere to regulations while maintaining the required load and efficiency. The results were a 48% reduction in NOx emissions and a 75% reduction in CO emissions.
Multiple boiler configuration plants can offer opportunities to improve efficiency. Automatic controllers with cost-objective functions for boilers can shift loads accordingly to maximize efficiency and reduce energy costs.
In this case study, a chemical company needed to find the most efficient operating point for each of its two utility boilers that were generating steam. Analysis determined the boiler fuel to steam ratio and the marginal production curve. The boiler fuel to steam ratio was found to be quasi-concave. As described below, based on these relationships, the company used APC and optimal load switching on these boilers and decreased fuel cost by 3%.
The MPC control scheme reduced the variability of the steam temperature three to five times better than the proportional-integral (PI) controllers. Regulatory PI controllers provide adequate steady state performance; however, APC can handle interaction and provide more responsiveness and stable operation.

Зображення


Догори
 Профіль  
 
Відображати повідомлення за:  Сортувати за  
Створити нову тему Відповісти  [ 1 повідомлення ] 

Часовий пояс UTC + 2 годин [ DST ]



Хто зараз онлайн

Зараз переглядають цей форум: Немає зареєстрованих користувачів і 2 гостей


Ви не можете створювати нові теми у цьому форумі
Ви не можете відповідати на теми у цьому форумі
Ви не можете редагувати ваші повідомлення у цьому форумі
Ви не можете видаляти ваші повідомлення у цьому форумі
Ви не можете додавати файли у цьому форумі

Знайти:
Вперед:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Вы можете бесплатно создать форум PHPBB2 на MyBB2.ru, Также возможно создать форум бесплатно PHPBB3 на Getbb.ru
Український переклад © 2005-2007 Українська підтримка phpBB