Форум АСУ в Україні http://asu.in.ua/ |
|
Професія: Automation Technician (Слюсар КВПіА) http://asu.in.ua/viewtopic.php?f=257&t=1113 |
Сторінка 1 з 6 |
Автор: | san [ 12 травня 2015, 16:30 ] | ||||
Тема повідомлення: | Професія: Automation Technician (Слюсар КВПіА) | ||||
Automation Technician (Слюсар КВПіА) http://www.automationfederation.org/fil ... nician.pdf Alternate Titles: Instrument Technician, Instrumentation Technician, Control Technician, Process Control Technician, Instrumentation and Electrical (I&E) Technician, Electrical and Instrumentation (E&I) Technician, and Measurement Technician. Sometimes called Instrument Mechanic, Control Mechanic.
Sources of Material: Certified Control System Technician Body of Knowledge, Automation Competency Model. |
Автор: | san [ 12 травня 2015, 18:11 ] |
Тема повідомлення: | Re: Професія: Automation Technician |
Performance Domains (Область діяльності): - Domain I: Calibration (Градуювання) - Domain II: Loop Checking (Ехо-контроль) - Domain III: Troubleshooting (Вирішення пробелм) - Domain IV: Start-Up (Запуск) - Domain V: Maintenance/Repair (Обслуговування/Ремонт) - Domain VI: Project Organization (Організація проектних робіт) - Domain VII: Administration (Адміністрування) |
Автор: | san [ 12 травня 2015, 18:14 ] |
Тема повідомлення: | Re: Професія: Automation Technician |
Domain I: Calibration (Калібрування) Task 1: Obtain all documents needed for device calibration in order to proceed with calibration. (Задача 1: Добувати (знаходити) всі документи, необхідні для калібрування пристрою для того, щоб приступити до калібрування) Knowledge of (знання): - Data sheets (специфікації) - Calibration sheets (калібровочні таблиці) - P&ID drawings (схеми P&ID) - Loop sheets (таблиці контурів) - Site procedures (процедури перевірки за місцем) - Mechanical and electrical drawings (електричні схеми та креслення конструкцій) Skill in (уміння): - Interpreting drawings (розуміння схем) - Searching technical information (пошук технічної інформації) - Communication (комунікації) - Following site procedures (слідування процедурам перевірки за місцем) |
Автор: | san [ 12 травня 2015, 18:15 ] |
Тема повідомлення: | Re: Професія: Automation Technician |
Task 2: Identify the correct device to be calibrated through documentation and instrument identification systems in order to ensure proper calibration. (Задача 2: Знайти необхідний пристрій для калібрування через документацію та систему ідентифікації приладів для забезпечення правильності калібрування) Knowledge of (знання): - Applicable standards (стандарти що застосовуються) - Site documentation (документація розташування) Skill in(уміння): - Interpreting data sheets (інтерпритація специфікацій) - Converting unit from metric/English or English/metric (переведення одиниць англ/метричні та навпаки) |
Автор: | san [ 12 травня 2015, 18:16 ] |
Тема повідомлення: | Re: Професія: Automation Technician |
Task 3: Select the correct test equipment through documentation and visual inspection as identified by site calibration procedures in order to correctly calibrate the device. Задача 3: Вибирати правильне тестове обладнання через документацію та візуальний огляд, як визначено процедурами калібрування по місцю, щоб правильно відкалібрувати пристрій Knowledge of: - Electrical and pneumatic test equipment (електричне та пневматичне тестове (перевірочне) обладнання) - Applicable standards on calibration of test equipment (стандарти по застосуванню на калібруванню тестового обладнання) - All appropriate procedures (усі відповідні процедури) - Acceptable certifying agencies, companies, etc. - Basic measurement units (основні одиниці виміру) Skill in: -Obtaining appropriate test equipment -Validating certification by matching or locating certification stickers -Using hand tools -Using test equipment |
Автор: | san [ 12 травня 2015, 18:17 ] |
Тема повідомлення: | Re: Професія: Automation Technician |
Task 4: Connect the test equipment to the device as required by manufacturer specifications and site procedures in order to properly and safely calibrate the device. Knowledge of: -Fundamentals of pneumatics -Fundamentals of electricity -Fundamentals of schematic diagrams -Basic physics of energy and power -Basic physical and chemical properties of matter -Basic temperature scales -Basic pressure units -Basic flow units -Basic level -Basic conversions -All appropriate site procedures -Manufacturer specifications Skill in: -Building a mechanical and electrical circuit, including piping, wiring circuits, and working with live circuits using test equipment -Using hand tools -Using test equipment -Using power sources -Using pressure sources |
Автор: | san [ 12 травня 2015, 18:19 ] |
Тема повідомлення: | Re: Професія: Automation Technician |
Task 5: Apply input values to the device as specified on instrument data sheet in order to simulate process parameters. Knowledge of: Fundamentals of pneumatics Fundamentals of electricity Fundamentals of schematic diagrams Basic physics of energy and power Basic physical and chemical properties of matter Basic temperature scales Basic pressure units Basic flow units Basic level Basic conversions and mathematics Manufacturers specifications Skill in: -Simulating a mechanical/pneumatic/electrical signal into a device -Using/working with high pressure sources, high temperature sources, voltage and current sources, etc. -Using hand tools -Using test equipment -Using power sources -Using pressure sources |
Автор: | san [ 12 травня 2015, 18:20 ] |
Тема повідомлення: | Re: Професія: Automation Technician |
Task 6: Record "as found" readings on calibration sheets in order to provide a history of the device. Knowledge of: Mathematics Physical sciences Conversions Electronic fundamentals Pneumatic fundamentals Skill in: Gathering technical information Writing Applying mathematical units and relationships Selecting required form |
Автор: | san [ 12 травня 2015, 18:21 ] |
Тема повідомлення: | Re: Професія: Automation Technician |
Task 7: Compare "as found" readings with the required values as specified by the instrument data sheet in order to identify if the device needs to be adjusted according to allowable tolerances. Knowledge of: Mathematics Physical sciences Conversions Electronic fundamentals Pneumatic fundamentals Skill in: Analyzing data Writing Applying mathematical units and relationships Selecting required forms |
Автор: | san [ 12 травня 2015, 18:23 ] |
Тема повідомлення: | Re: Професія: Automation Technician |
Task 8: Make adjustments to the device, if necessary, through site calibration procedures in order to ensure accuracy. Knowledge of: Calibration procedures Mathematics Physical sciences Electronic fundamentals Pneumatic fundamentals Electrical fundamentals Skill in: Working with tools Reading and interpreting test equipment Using power sources (electrical or pressure) Analyzing data |
Сторінка 1 з 6 | Часовий пояс UTC + 2 годин [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |